Clipinc.sh
Aus VDR Wiki
(Unterschied zwischen Versionen)
(M) |
(M) |
||
| Zeile 19: | Zeile 19: | ||
case "$1" in | case "$1" in | ||
-start) | -start) | ||
| − | + | if [ -s "${PIDFILE:=$2/clipinc.pid}" ] ; then | |
| − | if [ - | + | read PID < "$PIDFILE" |
| − | echo $"Clipinc process already active (pid: $PID)" ... | + | echo $"Clipinc process already active" "(pid: $PID)" ... |
else | else | ||
if pidof atd >/dev/null ; then | if pidof atd >/dev/null ; then | ||
if [ -e "$2/recinfo.conf" ] ; then | if [ -e "$2/recinfo.conf" ] ; then | ||
( | ( | ||
| − | echo "svdrpsend.pl -p ${VDR_PORT:-2001} MESG "$"Clipinc process started"" ... >/dev/null" | + | echo "clipinc.pl \"$2\" > $CLIPINC_LOGFILE 2>&1 &" |
| − | echo " | + | echo "PID=\$!" |
| − | echo "svdrpsend.pl -p ${VDR_PORT:-2001} MESG "$"Clipinc process finished"" ... >/dev/null" | + | echo "svdrpsend.pl -p ${VDR_PORT:-2001} MESG \""$"Clipinc process started"" (pid: \$PID) ...\" >/dev/null" |
| + | echo "echo \$PID > \"$PIDFILE\"" | ||
| + | echo "wait \$PID" | ||
| + | echo "rm -f \"$PIDFILE\"" | ||
| + | echo "svdrpsend.pl -p ${VDR_PORT:-2001} MESG \""$"Clipinc process finished"" (pid: \$PID) ...\" >/dev/null" | ||
) | at now | ) | at now | ||
else | else | ||
| Zeile 39: | Zeile 43: | ||
;; | ;; | ||
-kill) | -kill) | ||
| − | + | if [ -s "${PIDFILE:=$2/clipinc.pid}" ] ; then | |
| + | read PID < "$PIDFILE" | ||
| + | if ps -p $PID >/dev/null 2>&1 ; then | ||
| + | kill -9 $PID | ||
| + | fi | ||
| + | rm -f "$PIDFILE" | ||
| + | fi | ||
;; | ;; | ||
esac | esac | ||
Version vom 7. Januar 2006, 14:17 Uhr
Script für clipinc
#!/bin/sh
#
# clipinc.sh
#
# add this lines to your reccmds.conf:
# folgende zeilen in die reccmds.conf eintragen:
#
# Run clipinc : /path_to_this_script/clipinc.sh -start
# Stop clipinc? : /path_to_this_script/clipinc.sh -kill
# CONFIG START
CLIPINC_LOGFILE="/var/log/vdr/clipinc.log"
# CONFIG END
case "$1" in
-start)
if [ -s "${PIDFILE:=$2/clipinc.pid}" ] ; then
read PID < "$PIDFILE"
echo $"Clipinc process already active" "(pid: $PID)" ...
else
if pidof atd >/dev/null ; then
if [ -e "$2/recinfo.conf" ] ; then
(
echo "clipinc.pl \"$2\" > $CLIPINC_LOGFILE 2>&1 &"
echo "PID=\$!"
echo "svdrpsend.pl -p ${VDR_PORT:-2001} MESG \""$"Clipinc process started"" (pid: \$PID) ...\" >/dev/null"
echo "echo \$PID > \"$PIDFILE\""
echo "wait \$PID"
echo "rm -f \"$PIDFILE\""
echo "svdrpsend.pl -p ${VDR_PORT:-2001} MESG \""$"Clipinc process finished"" (pid: \$PID) ...\" >/dev/null"
) | at now
else
echo $"recinfo.conf not found" ...
fi
else
echo $"Jobmanager (atd) is not running" ...
fi
fi
;;
-kill)
if [ -s "${PIDFILE:=$2/clipinc.pid}" ] ; then
read PID < "$PIDFILE"
if ps -p $PID >/dev/null 2>&1 ; then
kill -9 $PID
fi
rm -f "$PIDFILE"
fi
;;
esac
