Clipinc.sh
Aus VDR Wiki
(Unterschied zwischen Versionen)
(+ tags) |
|||
| Zeile 41: | Zeile 41: | ||
find "\$CLIPINC2DIR" -type f -empty -exec rm -f '{}' ';' | find "\$CLIPINC2DIR" -type f -empty -exec rm -f '{}' ';' | ||
if [ ! -e "\$CLIPINC2DIR/\${LABEL##*/}.mp3" -a -f 001.vdr ] ; then | if [ ! -e "\$CLIPINC2DIR/\${LABEL##*/}.mp3" -a -f 001.vdr ] ; then | ||
| + | NAME="\${LABEL##*/}" | ||
| + | TITLE="\${NAME##*_-_}" | ||
| + | AUTHOR="\${NAME%%_-_*}" | ||
ffmpeg \ | ffmpeg \ | ||
| − | -i 001.vdr -acodec ${AUDIO_CODEC:-mp3} -ab ${AUDIO_BITRATE:-192} -ar ${AUDIO_SAMPLING:-44100} "$ | + | -i 001.vdr -acodec ${AUDIO_CODEC:-mp3} -ab ${AUDIO_BITRATE:-192} -ar ${AUDIO_SAMPLING:-44100} \ |
| + | \${TITLE:+-title "\$TITLE"} \${AUTHOR:+-author "\$AUTHOR"} "$CLIPINC2DIR/\$NAME.mp3" & | ||
wait | wait | ||
fi | fi | ||
Version vom 31. März 2005, 19:07 Uhr
#!/bin/sh
#
# clipinc.sh
#
# Required: at, clipinc.pl, lame, ffmpeg ('--enable-mp3lame')
#
# add this lines to your reccmds.conf:
# folgende zeilen in die reccmds.conf eintragen:
#
# Run clipinc : /usr/local/bin/clipinc.sh -start
# Run clipinc + 2mp3 : /usr/local/bin/clipinc.sh -start -2mp3
# Stop clipinc? : /usr/local/bin/clipinc.sh -kill
# CONFIG START
AUDIO_CODEC="" # force audio codec ('copy' to copy stream) -> default ('mp3')
AUDIO_BITRATE="" # set audio bitrate (in kbit/s) -> default ('192')
AUDIO_SAMPLING="" # set audio sampling rate (in Hz) -> default ('44100')
CLIPINC_LOGFILE="/var/log/vdr/clipinc.log"
# CONFIG END
PATH=/usr/local/bin:$PATH
case "$1" in
-start)
at now <<EOF
PID=`pidof -x clipinc.pl`
if [ -n "\$PID" ] ; then
svdrpsend.pl MESG "Sorry, but clipinc.pl is running with pid (\$PID)..."
else
if [ -e "$2/recinfo.conf" ] ; then
clipinc.pl "$2"
elif [ -e "$3/recinfo.conf" ] ; then
if [ $(ldd $(which ffmpeg) | grep -c libmp3lame.so) -lt 1 ] ; then
echo "Unsupported codec, 'configure' ffmpeg with ('--enable-mp3lame')..."
else
clipinc.pl "$3"
find "$CLIPINCDIR" -name "001.vdr" | sed '/\.rec\/001\.vdr/!d' | while read i ; do
cd "\$(echo \$i | sed -e 's/.\{8\}$//g')"
LABEL=\$(dirname "\$(pwd)")
find "\$CLIPINC2DIR" -type f -empty -exec rm -f '{}' ';'
if [ ! -e "\$CLIPINC2DIR/\${LABEL##*/}.mp3" -a -f 001.vdr ] ; then
NAME="\${LABEL##*/}"
TITLE="\${NAME##*_-_}"
AUTHOR="\${NAME%%_-_*}"
ffmpeg \
-i 001.vdr -acodec ${AUDIO_CODEC:-mp3} -ab ${AUDIO_BITRATE:-192} -ar ${AUDIO_SAMPLING:-44100} \
\${TITLE:+-title "\$TITLE"} \${AUTHOR:+-author "\$AUTHOR"} "$CLIPINC2DIR/\$NAME.mp3" &
wait
fi
done
fi
else
svdrpsend.pl MESG "recinfo.conf not found..."
fi
fi \
> $CLIPINC_LOGFILE 2>&1
EOF
;;
-kill)
PID=`pidof -x clipinc.pl`
eval ${PID:+kill -9 $PID}
;;
esac
